This site and contents herein are ©1998-2007, UltraVolt, Inc.



Products
"F" Series High Voltage Power Supply

PDF version is also available
Currently viewing page: 1 Jump to page: 1 2

Click here to request more information or to get a quote

“F” SERIES

HIGH VOLTAGE POWER SUPPLY

  • Encapsulated with “A” Series power supplies
  • Ripple Stripper® Output Filter
  • Ultra-low output ripple
  • Output voltage monitor
  • Fixed-frequency, low-stored-energy design
  • >400,000 Hrs MTBF @ 65°C
  • UL, cUL, IEC-60950-1, and Demko Recognized
  • GENERAL INFORMATION:
    The “F” Series of Ripple Stripper® accessories features a ripple-reduction circuit added internally to 62V through 6kV “A” Series HVPS modules prior to encapsulation at the factory.

    While adding a minimum of output capacitance and output impedance, output ripple is reduced >10 times! Output voltage regulation remains at <0.01% no load to full load. Also included is an Output Voltage Monitor. For greater performance the optional, wrap-around Mu-Metal shield should be used. The Ripple Stripper® accessory is also available on the “10A-25A” and "30A-40A" Series of HVPS. Please see the corresponding data sheets for specifications.

    HIGH VOLTAGE OUTPUT FILTER:
    The “F” Series strips the typical output ripple on “A” Series high-voltage power supplies down
    to:

    Model
    Voltage
    Power
    With
    -F
    With
    -F-M
    50% Lower than -F-M
    Ripple w/ Ext. Cap
    1/16A12 62V 4W <0.002% <0.002% .5uF / Metal Film
    1/16A24 62V 20W <0.003% <0.004% .5uF/ Metal Film
    1/16A24 62V 30W <0.006% <0.006% .5uF/ Metal Film
               
    1/8A12 125V 4W <0.002% <0.0048% .5uF / Metal Film
    1/8A24 125V 20W <0.008% <0.0056% .5uF / Metal Film
    1/8A24 125V 30W <0.006% <0.006% .5uF / Metal Film
               
    1/4A12 250V 4W <0.0012% <0.0052% .047uF/ Metal Film
    1/4A24 250V 20W <0.004% <0.0028% .047uF/ Metal Film
    1/4A24 250V 30W <0.0032% <0.005% .047uF/ Metal Film
               
    1/2A12 500V 4W <0.0006% <0.001% .022uF/ Metal Film
    1/2A24 500V 20W <0.002% <0.0138% .022uF/ Metal Film
    1/2A24 500V 30W <0.025% <0.0016% .022uF/ Metal Film
               
    1A12 1kV 4W <0.0005% <0.0005% .05uF/ Metal Film
    1A24 1kV 20W <0.001% <0.0008% .05uF/ Metal Film
    1A24 1kV 30W <0.003% <0.002% .05uF/ Metal Film
               
    2A12 2kV 4W <0.0036% <0.0007% 4700pF/X7R
    2A24 2kV 20W <0.0063% <0.0038% 4700pF/X7R
    2A24 2kV 30W <0.015% <0.004% 4700pF/X7R
               
    4A12 4kV 4W <0.0063% <0.0004% 1500pF/X7R
    4A24 4kV 20W <0.0051% <0.0088% 1500pF/X7R
    4A24 4kV 30W <0.0094% <0.0026% 1500pF/X7R
               
    6A12 6kV 4W <0.0135% <0.0003% 1500pF/X7R
    6A24 6kV 20W <0.0086% <0.0012% 1500pF/X7R
    6A24 6kV 30W <0.02% <0.004% 1500pF/X7R

     

    HIGH VOLTAGE OUTPUT:
    Square .025in pins are used for high-voltage output and high-voltage return. These pins can be used for PCB mounting or for direct wiring.

    OUTPUT VOLTAGE MONITOR:
    The “F” Series features a 100:1 voltage monitor on pins 12 and 13 referenced to Signal Ground pin 5. The monitor output impedance is calibrated for use with a 10 MegΩ input impedance meter. Units 2kV or higher have a 100 MegΩ/1.1 MegΩ divider; units below 2kV use a 10 MegΩ/102k divider. Overall accuracy is ± 2.5% with a temperature coefficient of ±200 ppm per °C.

    For applications requiring a different scale factor, such as an ADC compatible design, an external resistor may be added in parallel with the output.

    SHIELDING:
    All models are available with optional, six-sided, wraparound Mu-Metal Shielding. This shielding attenuates magnetic and electrostatic emissions, while shielding ripple reduction circuitry from outside noise.

    MECHANICAL:
    The “F” Series accessories are designed to be added to the basic “A” Series HVPS module. The combined plastic package has a footprint of only 7.0in², a volume of just 6.35in³, and a weight of 7 oz. Mounting plates and brackets are available for chassis mounting. This series is also available in an RF-tight, metal PCB/chassis mount package. The combined metal package has a footprint of only 10.7in², a volume of just 11.8in³, and a weight of 13 oz.

    ENVIRONMENT:
    The “F” Series meets the same environmental specifications for temperature, shock, and vibration as the “A” Series. All units receive a 24-hour burn-in prior to final test. Extended temperature range is available along with other enhanced capabilities. Please contact the factory.


    1800 OCEAN AVE., FRNT
    RONKONKOMA, NY 11779

    TEL 800-9HV-POWER
    TEL 631-471-4444
    FAX631-471-4696

    www.ultravolt.com

    next page

    © 2003-2007 UltraVolt, Inc.
    specifications subject to change without notice


    UltraVolt, Inc.
    1800 Ocean Ave. Frnt
    Ronkonkoma, NY 11779
    1-800-9HV-POWER
    1-800-948-7693
    631-471-4444
    Fax: 631-471-4696
    E-mail: csd@ultravolt.com