Parameter |
Conditions |
Models |
Units |
Input: |
All
Types |
|
Voltage Range |
Full
Power |
+ 23 to 30 |
VDC |
Voltage Range |
Derated Power Range |
+ 9 to 32 |
VDC |
Current |
Standby
/ Disable |
< 30 |
mA |
Current |
No
Load, Max Eout |
< 90 |
mA |
Current |
Max
Load, Extended Input Voltage |
Figures A & B |
Graph |
AC
Ripple Current |
Nominal
Input, Full Load |
< 80 |
mA p-p |
Output: |
1/16C |
1/8C |
1/4C |
1/2C |
1C |
2C |
4C |
6C |
|
Voltage Range |
Nominal Input |
0 to 62 |
0 to 125 |
0 to 250 |
0 to 500 |
0 to 1,000 |
0 to 2,000 |
0 to 4,000 |
0 to 6,000 |
VDC |
Power |
Nominal Input, Max Eout |
20 |
30 |
20 |
30 |
20 |
30 |
20 |
30 |
20 |
30 |
20 |
30 |
20 |
30 |
20 |
30 |
Watts |
Current |
Iout, Entire Output Voltage Range |
320 |
480 |
160 |
240 |
80 |
120 |
40 |
60 |
20 |
30 |
10 |
15 |
5 |
7.5 |
3.3 |
5 |
mA |
Ripple |
Full Load, Max Eout, Cload ≥ 0.5uF |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
< 1.0 |
V p-p |
Overshoot |
C Load, 0 Eout to Full Eout |
<1V |
<1V |
<1V |
<1V |
<1V |
<1V |
<2V |
<2V |
<2V |
<2V |
<0.1% |
<0.1% |
<0.1% |
<0.1% |
<0.1% |
<0.1% |
V pk |
Voltage Derating |
Max Iout, Extended Input Voltage |
Figures C |
Graph |
Rise Time |
Max Iout, Various C Loads & Eout |
Figures D & F |
Table |
Line Regulation |
Nom. Input, Max Eout, Full Power |
< 0.01 % |
VDC |
Static Load Regulation |
No Load to Full Load, Max Eout |
<0.01% |
VDC |
Stability |
30 Min. warmup, per 8 hr/ per day |
<0.01% / <0.02% |
VDC |
Output
Voltage Monitor: |
All
Types |
|
Voltage |
Full Eout Range, Full Iout Range |
10.00 |
V per kV |
Proportionality |
Full Eout Range, Full Iout Range |
± 0.1% |
V per kV |
Remote
Programming: |
All
Types |
|
Input Impedance |
Nominal Input |
+ Output Models 1.1MΩ to GND, - Output Models 1.1MΩ to +5 Vref |
MΩ |
Adjust Resistance |
Typical Potentiometer Values |
10K to 100K (Pot across
Vref.
& Signal GND, Wiper to Adjust) |
Ω |
Adjust Linearity |
0% to 100% |
Figure E |
Graph |
Adjust Voltage |
Referenced to signal ground |
Figure E (0 to +5
VDC) |
Graph |
Adjust Logic |
0 to +5 for +Out, +5 to 0 for -Out |
+4.64 VDC for +Output or
+0.36 for -Output = Nominal Eout |
|
Reference: |
All
Types |
|
Output Voltage |
T=+25°C, Initial Value |
+ 5.00 ± 2% |
VDC |
Output Impedance |
T=+25°C |
464 ± 1% |
Ω |
Stability |
Over Full Temperature Range |
See “A” Series
Datasheet Figure F |
Graph |
Enable: |
All
Types |
|
Power Supply On |
Floated, or voltage ≥ TTL High |
+2.4 to 32 |
VDC |
Power Supply Off |
Grounded, or voltage ≤ TTL Low |
0 to + 0.7 ± 0.2 (Isink 1mA minimum) |
VDC |
Temperature & Humidity: |
Standard |
-25PPM |
|
Humidity |
All Conditions, Standard Package |
0 to 95% non-condensing |
0 to 95% non-condensing |
|
Operating |
Full Load, Max Eout, Case Temp. |
-40 to +65 |
+10 to +45 |
°C |
Storage |
Non-Operating, Case Temp. |
-55 to +105 |
-55 to +105 |
°C |
Coefficient |
Over the Specified Temperature |
± 50 |
± 25 |
PPM / °C |
Thermal Shock |
Mil-Std 810, Method 503-4, Proc. II |
-40 to +65 |
-40 to +65 |
°C |
Altitude: |
All
Types |
|
All Conditions |
Standard Package |
Sea Level through Vacuum |
|
Shock & Vibration: |
Standard |
-
C Option |
|
Shock |
Mil-Std-810, Method 516.5, Proc. IV |
20 |
40 |
G's |
Vibration |
Mil-Std-810, Method 514.5, Fig. 514.5C-3 |
10 |
20 |
G's |
Packaging: |
Standard |
-
C Option |
|
Material |
Outer construction |
Plastic (DAP) ASTM-D-5948 |
Aluminum Alloy 5052-H32,
Finish: Mil-C-5541 Class 1A |
|
Length |
Not including pins or mounting pts |
3.70 ± 0.050 (94.0) |
4.75 ± 0.025 (120.7) |
In (mm) |
Width |
Not including pins or mounting pts |
1.50 ± 0.050 (38.1) |
2.00 ± 0.025 (50.8) |
In (mm) |
Height |
Not including pins or mounting pts |
0.77 ± 0.050 (19.6) |
1.00 ± 0.025 (25.4) |
In (mm) |
Volume |
Not including pins or mounting pts |
4.30 (70.5) |
8.00 (131.1) |
In³ (cc) |
Weight |
Overall |
5.0 (142) |
10.0 (284) |
Oz (g) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Rev. T 8/07
